Ultem 1010-1000

Ultem 1010-1000

厂家(产地)：	SABIC	牌号：	1010	类型：	标准料
断裂伸长率：	60	规格级别：	注塑	拉伸强度：	104.8
密度：	1.27	弯曲模量：	3309.49	吸水率：	1.25
查看全部参数>

SABIC Innovative Plastics Ultem 1000 PolyetherimideCategories:Polymer; Thermoplastic; PolyetherimideMaterial Notes:Transparent, standard flow Polyetherimide (Tg 217C). ECO Conforming, UL94 V0 and 5VA listing. US FDA and EU Food Contact compliant, NSF 51 listing, compliant in natural color.This data was supplied by SABIC-IP for the Americas and Asia Pacific regions. MatWeb with separate data for the Europe-Africa-Middle East region as supplied by SABIC-IP as of August 2009.Vendors:No vendors are listed for this material. Please click here if you are a supplier and would like information on how to add your listing to this material.Physical PropertiesMetricEnglishCommentsSpecific Gravity1.27 g/cc1.27 g/ccASTM D 792Water Absorption0.25%0.25%24 hrs; ASTM D 570Water Absorption at Saturation1.25%1.25%ASTM D 570Linear Mold Shrinkage0.00500 - 0.00700 cm/cm0.00500 - 0.00700 in/inflow; SABIC Method@Thickness 3.20 mm@Thickness 0.126 inMelt Flow9.00 g/10 min9.00 g/10 minASTM D 1238@Load 6.60 kg,@Load 14.6 lb,Temperature 337 °CTemperature 639 °FMechanical PropertiesMetricEnglishCommentsHardness, Rockwell M109109ASTM D 785Tensile Strength, Yield110 MPa16000 psiType I, 5 mm/min; ASTM D 638Elongation at Break60.00%60.00%Type I, 5 mm/min; ASTM D 638Elongation at Yield7.00%7.00%Type I, 5 mm/min; ASTM D 638Tensile Modulus3.58 GPa519 ksi5 mm/min; ASTM D 638Flexural Modulus3.51 GPa509 ksi2.6 mm/min, 100 mm span; ASTM D 790Flexural Yield Strength165 MPa23900 psi2.6 mm/min, 100 mm span; ASTM D 790Poissons Ratio0.30.3ASTM D 638Izod Impact, Unnotched13.35 J/cm25.01 ft-lb/inASTM D 4812@Temperature 23.0 °C@Temperature 73.4 °FGardner Impact36.0 J26.6 ft-lbASTM D 3029@Temperature 23.0 °C@Temperature 73.4 °FTaber Abrasion, mg/1000 Cycles1010CS-17, 1 kg; ASTM D 1044Izod Impact, Notched0.530 J/cm0.993 ft-lb/inASTM D 256@Temperature 23.0 °C@Temperature 73.4 °F13.35 J/cm25.01 ft-lb/inReverse Notched; ASTM D 256@Thickness 3.20 mm@Thickness 0.126 inElectrical PropertiesMetricEnglishCommentsVolume Resistivity1.00e+17 ohm-cm1.00e+17 ohm-cmASTM D 257Dielectric Constant3.153.1**STM D 150@Frequency 1000 Hz@Frequency 1000 Hz3.153.1**STM D 150@Frequency 100 Hz@Frequency 100 HzDielectric Strength19.6 kV/mm498 kV/inin oil; ASTM D 149@Thickness 3.20 mm@Thickness 0.126 in27.9 kV/mm709 kV/inin oil; ASTM D 149@Thickness 1.60 mm@Thickness 0.0630 in32.7 kV/mm831 kV/inin air; ASTM D 149@Thickness 1.60 mm@Thickness 0.0630 inDissipation Factor0.00120.0012ASTM D 150@Frequency 1000 Hz@Frequency 1000 Hz0.00150.001**STM D 150@Frequency 100 Hz@Frequency 100 Hz0.00250.002**STM D 150@Frequency 2.45e+9 Hz@Frequency 2.45e+9 HzArc Resistance120 - 180 sec120 - 180 secTungsten; PLC Code 5; ASTM D 495Comparative Tracking Index100 - 175 V100 - 175 VUL 746AHot Wire Ignition, HWI60.0 - 120 sec60.0 - 120 secPLC 1; UL 746AHigh Amp Arc Ignition, HAI15.0 - 30.0 arcs15.0 - 30.0 arcssurface; UL 746AHigh Voltage Arc-Tracking Rate, HVTR25.4 - 80.0 mm/min1.00 - 3.15 in/minPLC 2; UL 746AThermal PropertiesMetricEnglishCommentsCTE, linear55.8 µm/m-°C31.0 µin/in-°FFlow; ASTM E 831@Temperature -20.0 - 150 °C@Temperature -4.00 - 302 °FCTE, linear, Transverse to Flow54.0 µm/m-°C30.0 µin/in-°FASTM E 831@Temperature -20.0 - 150 °C@Temperature -4.00 - 302 °FThermal Conductivity0.220 W/m-K1.53 BTU-in/hr-ft²-°FASTM C 177Deflection Temperature at 0.46 MPa (66 psi)210 °C410 °Funannealed; ASTM D 648@Thickness 6.40 mm@Thickness 0.252 inDeflection Temperature at 1.8 MPa (264 psi)201 °C394 °Funannealed; ASTM D 648@Thickness 6.40 mm@Thickness 0.252 inVicat Softening Point218 °C424 °FRate B/50; ASTM D 1525Glass Transition Temp, Tg217 °C423 °FUL RTI, Electrical170 °C338 °FUL 746BUL RTI, Mechanical with Impact170 °C338 °FUL 746BUL RTI, Mechanical without Impact170 °C338 °FUL 746BNBS Smoke Density0.70.7Flaming, Ds 4 min; ASTM E 662Oxygen Index47.00%47.00%ASTM D 2863Descriptive PropertiesCSA File NumberLS88480CSA LISTED

宁波市江东开迪贸易有限公司提供Ultem 1010-1000，真诚欢迎您的到来。